Ron Pope Motorsports                California Custom Roadsters               

Windshield Frame Material

RESINATOR said:
CCR is a manufacture and supplier for the Windshield Frame Material and we would like to make the material available to the Forum Members at a special price. The Material is extruded solid Aluminum and is weldable and bendable. We sell this by the foot and we will hold the price until the end of January 2012.

Part # 58541-TBF $ 6.25 per foot

We will cut the Material to your size free of charge. (straight cuts)

Thanks, hope this helps.

Jerry and Diane
Click to expand...
Could you quote me a shipped price for 2 Ea 4' and 2 ea 2' shipped to 86401
Kingman Az
Terry
 
Do you have dimension info on your short w/s posts? Looking for hole distances & other dimensions. Yours look to be fairly close to what I have & I'm trying to determine if they'd fit my body or come close.

If I were to purchase a set to try, can I return them w/ no problem if they are way off?

I'm fairly sure I'd like to hit you up for a 14" windshield frame in the spring. I currently have a 2 pc tall windshield & I can't deal w/ the top glass swinging anymore. It's been impossible to remedy.

thanks for any info!

Karri
 
I guess posts can't be edited...?

I mean, I have tall posts & the mounting area on CCR posts looks pretty similar to mine, otherwise I'll end up cutting mine down & using them w/ a shorter 1 pc windshield. My posts are also laid back a wee bit & I would prefer a more straight/vertical mounting, but I could live w/ them if necessary. No idea the manufacturer. The body came out of Cleveland, OH 1971.

thanks again
 
I will have to get the dimensions for you, but the best thing for you to do if your body is already painted is to cut down what you have ( assuming they fit well). The tall posts seem to have a flatter area above the holes and in the past we would need to fit/grind the body to get those type of posts to mate to the body.
You are certainly welcome to order them and gently check the fit to your body, but the posts would have to come back to us in the condition you receive them.
I will get a few dimensions with photos and post in a while.

Windshield Posts szd (1).jpg Windshield Posts szd (4).jpg Windshield Posts szd (8).jpg
 
thx, very helpful! I'll take a closer look at mine, they were made for my body in the early 70's, cutting them may be my best option.
What dimensions do you need to make a frame? Would I measure my existing frame, outside corners (mine seems narrower than what is common these days) or the distance to the inside of my posts?
Thanks again.
Mine, for reference:



post.jpg post1.jpg post2.jpg
 
I hope this turns out to be easier for you than it was for me. Even with Jerry's considerable help, it was a huge amount of work changing from lay back to straight posts (plus a taller windshield). The problem was that whoever built the car failed to contour the body to fit the posts. I didn't want to repaint the body, so I spent hours reshaping the new straight-up posts with various grinding wheels. I'll still need to remove them sometime in the spring for powder coating. Incidentally, I wouldn't cut down those long posts until you check to see how much they're worth. In fact, even if they're only worth as much as new short posts, they might be very useful to someone who needs taller posts.

Jack
 
Thanks. Mine would get cut if any work would have to be done to fit other posts & it would be the easiest thing to do & ensure that it fits properly the first time around. Mine were made for my body & while they lay back, it's only slight. Even if someone did need taller posts, they'd likely have to put just as much work into getting these to fit their body as I would new ones & I'm not doing any bodywork to my T.

My dad built this car from the ground up when I was a baby & even thinking about changing the windshield is giving me a huge guilt trip, but I can't stand the damn thing swinging like a cat door before I get 200 ft out of the driveway. I'm constantly tightening it.
 
The windshield frame should fit snug into the pocket of the posts, yours looks like it could be a little narrow and fit loose once cut down.
Once you cut the posts off to the length you want, bolt them back up to the body and give me a dimension across at the bottom of the post (at the dash top) and then across the top of the posts. This will account for any tilt angle the post may have. We will make a frame to those dimensions for you.
Also, you need to let us know if you want a full frame around the glass or the top edge of glass exposed. Height is important if you use a full frame because you will not want to be looking thru the frame.
You may also want to consider drilling two holes per side on the posts to improve the fit/stiffness before you cut off too much of the post height.
 
PeppermintPatty said:
...I can't stand the damn thing swinging like a cat door before I get 200 ft out of the driveway.
Click to expand...
I'll bet there's a much easier solution for that than changing out the entire windshield. Maybe someone here will have an idea if you post a few closeup shots of the hinge and clamp.

Jack
 
As far as the hinge/clamp goes...They are basic tall posts w/ the swivels/wingnuts/threaded rod at the top of the posts, nothing uncommon. Speedway still sells this style as well as others do. I've tightened them so much, one nut had stripped. I bought new swivels & new nuts, think maybe because of age, the originals could have wear issues even though they appear fine. They hold for a while, but get on a rough road & they instantly come loose. I live on a gravel drive & by the time I get to the top of my road to the pavement, I have to stop & tighten again. I don't know how much rods would help this issue, it doesn't seem like it would affect the side to side shake that seems to be the problem. I don't care for the way they look either.

I had planned on running a tape line across the current glass to get a feel for height, I'd like a full, square-cornered frame (not rounded). I was going to ask you advice about fastening it & the two holes per side is what I was wondering. Thanks again, I think this is enough info to get a good idea what I need to do.
 
I had a 2 piece w/s in my car and I drilled a small hole in the upright and put a self tapping screw into the upper frame at the bottom edge and it stopped the swing. John
 
old round fart said:
I had a 2 piece w/s in my car and I drilled a small hole in the upright and put a self tapping screw into the upper frame at the bottom edge and it stopped the swing. John
Click to expand...
Could one maybe use a dowel(s)/stud in the windshield register? Facing up into a slot or hole it would be hidden by the bottom of the frame. Just a thought.
 
Hey Jerry, I realize this post started a long time ago, what is your price on the aluminum now per foot?
 
You must log in or register to reply here.

Similar threads

JetMech727
CCR Windshield Frame
2
Replies
34
Views
16K
JetMech727
JetMech727
Indycars
Evolution of a Windshield
Replies
7
Views
4K
AusBucket
A
C cab t
Windshield Frame
2
Replies
23
Views
5K
Hot Rod Tommy T
Hot Rod Tommy T
RESINATOR
CCR's Standard T Body Sale.
Replies
1
Views
5K
Bellingson
B
Keeper
Windshield frame material supplier
Replies
10
Views
6K
Keeper
Keeper

     Ron Pope Motorsports                Advertise with Us!     
Back
Top