Ron Pope Motorsports                California Custom Roadsters               

Search results

  1. benT

    Progressive Throttle Linkage ???'s

    Both my '27 and my dads run dual quad intakes with Edelbrock 500's with the edelbrock progressive linkage. The progressive linkage works great and they both ron good for being mild small blocks. Most of the time the car runs on the back carb, but when you get on it the front carb kicks in. I...
  2. benT

    Need Spark Plug Wire Recommendation

    I've used Taylor wires for 25+ years now on all my hot rods. The 8mm spiro-pro wires come in a variety of colors and and they have 90, 180, and 135 degree angle boots. I typically get the cut to length sets so I can run them the way I want. The ability to have a great quality wire - USA made...
  3. benT

    Cool 60's show T for sale...

    If anyone here was looking for an authentic 60's show T in pretty original condition, check this out. Price seems steep, but this car does have the right look and parts. Pretty cool! 1965 Built SHOWROD FabT T Bucket Mint Julep Cragar Blower Magnesium
    • benT
    • Thread
    • Replies: 0
    • Forum: Lounge
  4. benT

    Jarrett's 27 roadster

  5. benT

    Jarrett's 27 roadster

    yeah, but check out the RPM they are pulling to make that power. Yes the 305 will rev pretty good, but I prefer more grunt and power at a lower, street friendly rpm (Jarrett isn't racing this ya know) - the Super Victor intake isn't exactly the best for that. Although I like the idea of using...
  6. benT

    Fan shroud depth

    2 Old is right. Ours are about 1" deep. If you have more room it would probably help. Our shop does work with C&R Radiators - they stress that he shroud must be tight and sealed properly, or it will be inefficient.
  7. benT

    Jarrett's 27 roadster

    Actually, thats my pops '27. Mine is the blue one here:
  8. benT

    Jarrett's 27 roadster

    Not to get sidetracked, but from what I've read in the last year or so, the newer Rotella has way less zddp or zinc in it then it used to. We've switched to Lucas "Hot Rod" oil which is formulated with the larger doses of zinc and is made for older engines with flat tappet cams. You may be...
  9. benT

    Nationals

    Go to the NTBA website/forum for info on all the events: National T-Bucket Alliance - Events
  10. benT

    What is everybody doing?

    I'm buried at work -which also doubles as our hot rod shop, so I get to see all three of our cars collecting dust everyday... We still have to rebuild the short block on the Purple Powder Pickup as the '66 stock bore 283 is wore out - gonna get a fresh bore and new slugs. Mine needs some minor...
  11. benT

    Getting the T Bucket done

    Go to a few NTBA regional events and get a couple ride-a-longs and it will pump you back up. Make a deadline for an event and it will help keep you getting on it. Maybe a regional event near you next year?
  12. benT

    T Bucket Interiors

    I had a limeworks 14" 4 spoke wheel on my '27. It was the same as the photo above, but with the holes. After 8 years of frequent driving, it developed cracks between the holes and one spoke broke. The steel used for the spokes should have been a bit thicker - it measures only .110". I loved...
  13. benT

    Photo.... Do NOT Fold

    We got one as well- faired pretty much the same- folded in half! Thanks Ron!
  14. benT

    3" drop

    Ron does make tube dropped axles.
  15. benT

    3" drop

    I bet Ron Pope @RPM can make one for you. His link is at the top of the page.
  16. benT

    Be VERY careful out there.

    I have 8 mounting points on my '27. All fasteners have large washers on the floor side and bolts go through gusseted frame mounts welded to the frame. I would never trust riv-nuts into the frame or any of the "expandable" fasteners that are sold by some of the hot rod suppliers.
  17. benT

    Kit Car Rego Recinded?

    The basis for this was the "off-road" nature of rails and buggies. I actually read through the Texas's assembled vehicle manual after reading an article on this and actually found texas very clear and specific on the manner to license and title a hot rod type vehicle. The manual gives...
  18. benT

    New to T's

    Welcome from Indy!
  19. benT

    new to T's 27?

    IF you want a '27 Kit, your best bet is Spirit Cars which is a sponsor her (see top of forum and click). Josh @Hulkamania on this forum is one of the key guys there and can answer any questions. Speedway also has a '27 kit as well. Not sure if anyone else has a "kit" for the '27s. CCR (Also a...
  20. benT

    T Bucket Interiors

    I think this one was a late 80's or early 90's. As for swamp dogs concern, the back foam could certainly be cut thinner by the upholstery guy, but as Dennis is about 6' and 200, he fits fine.

     Ron Pope Motorsports                Advertise with Us!     
Back
Top