Ron Pope Motorsports                California Custom Roadsters               

Search results

  1. L

    Routing of Wires?

    Hi Everyone! I'm getting ready to wire up my T and i was wondering if you guys run your wires in your frame or on the out side. I was thnking of running mine inside the frame for neater look but I didn't know if that was common practice.... Really it would be just the headlight wires, engine...
  2. L

    4L80E to a th350? Need some help with the Flexplate!

    Thanks for your Help!! I did get the correct flexplate and all is good!!! Thanks again!
  3. L

    4L80E to a th350? Need some help with the Flexplate!

    Thanks for the reply's The original flywheel has 168 teeth with six holes. I tried lining up the holes on the one I have with the converter and they are off(Won't line up)....
  4. L

    4L80E to a th350? Need some help with the Flexplate!

    Hi everyone, I started working on my T bucket again and I just got my trans back from the shop and discovered a little problem. I'm running a 1996 350 out of a one ton van that had a 4L80E hooked to it. I got rid of that trans and want to use the TH350 I just had rebuilt. The original flex...
  5. L

    Master Cylinder Part #'s

    Thanks I ordered one Today!!!
  6. L

    Master Cylinder Part #'s

    Hi Everyone. I know someone has posted these part numbers but I can't seem to find them. I'm running a disk/drum set up on my T and was looking for a napa master cylinder part #. I'm using a pedal/master cylinder mounting bracket from Total Performance. Thanks!!!
  7. L

    Would like to fit the body over the frame... Any tips?

    Floor to top of the side is 20.5 inches. I think I still have enough room to do this. Looks like it will come right up to the bottom of the door just like Don's. Do you guys use wood for the floor of your cars? Thanks for all the input guys...;)
  8. L

    Would like to fit the body over the frame... Any tips?

    Hi Everyone, I'm starting to work on the T again and would like to set the body over the frame so it has a lower apperance. I would like to drop it about 3 inches. Any tips on what the best way to do this is? I've posted a few pics of the body. It is an older one. Not sure who made it.... Thanks...
  9. L

    Rear spring shackle question!!!

    Thanks for all the help guys. I talked to RPM and he's setting me up with everything I need. I'm hoping on getting everything in the car in the next couple of weeks. I will let you know how I make out. Thanks again!!
  10. L

    Rear spring shackle question!!!

    Ted, When you say bushings, r u talking about rubber bushings. I'm trying to figure out where they would go. On the Hair pin you have three mounting points that normally would use a clevis and 5/8" bolt? Where would the bushing mount? Thanks
  11. L

    Rear spring shackle question!!!

    I see RPM has a nice set of hair pins that includes everyting I need. Those should work fine. I think that would be a smart move on my part. I'm trying to figure out what the rear housing brackets look like. Do you have a pic? Thanks again for all your help!!:)
  12. L

    Front spring worn out?

    Thanks for alll the help guys!! I took the spring out tonight.... I found that the spring perch has a 1/2" hole instead of a 3/4" hole.... Must be the original perch??? I think I will do just what Youngster said... I will buy a new spring, shackles and perches. That should clean up the front...
  13. L

    Front spring worn out?

    I'm trying to get the suspension on this car squared away and have a few "Rookie" questions. I was looking at the front end and noticed that the spring looks worn out. It's almost flat across the top. The spring is mounted above the axle and it if I stand on it I can get the spring to bottom out...
  14. L

    Rear spring shackle question!!!

    I have a 1923 t bucket that is using what I beleiive is the original spring. The bushings were worn out on the shackles so I decided to replace them. I ordered a set of 2" shackles from speedway and they really don't fit correctly. They mount the spring to close to the bracket. I posted a couple...
  15. L

    Looking to add a small pick up bed to my T

    Do they have a website? Thanks
  16. L

    Looking to add a small pick up bed to my T

    Thanks for your input!!!! The keg looks a little bigger in the pics than it really is. It only holds about 10 gallons. If I add the bed I was going to to away with the keg and get a tank from rpm. The other thought I had was to just do away with all the stuff on the back end and just build a...
  17. L

    Looking to add a small pick up bed to my T

    Hi All, I'm finally starting to work on my bucket again. I would like to get rid of the dune buggy looking thing thats currently on my T(See Pics) and add a small pick up bed. I see speedway anf TP have these in both 14" and 20". My questions is can I add this with out doing any fiberglass work...
  18. L

    318 T-Bucket headers??

    Yeah, I wish I would have posted this 3 years ago. Would have loved to find a used set.:lol:Thanks for the reply.
  19. L

    318 T-Bucket headers??

    OK Thanks I have the LA engine. Thanks for your help
  20. L

    318 T-Bucket headers??

    Thanks for all the replies. I guess I'm not really sure what 318 I have. How do I tell which one i have? Thanks

     Ron Pope Motorsports                Advertise with Us!     
Back
Top